/**
  ******************************************************************************
  * @file    stm32746g_discovery.c
  * @author  MCD Application Team
  * @brief   This file provides a set of firmware functions to manage LEDs, 
  *          push-buttons and COM ports available on STM32746G-Discovery
  *          board(MB1191) from STMicroelectronics.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */ 

/* Dependencies
- stm32f7xx_hal_cortex.c
- stm32f7xx_hal_gpio.c
- stm32f7xx_hal_uart.c
- stm32f7xx_hal_i2c.c
EndDependencies */

/* Includes ------------------------------------------------------------------*/
#include "stm32746g_discovery.h"

/** @addtogroup BSP
  * @{
  */ 

/** @addtogroup STM32746G_DISCOVERY
  * @{
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL STM32746G_DISCOVERY_LOW_LEVEL
  * @{
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Private_TypesDefinitions STM32746G_DISCOVERY_LOW_LEVEL Private Types Definitions
  * @{
  */
/**
  * @}
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Private_Defines STM32746G_DISCOVERY_LOW_LEVEL Private Defines
  * @{
  */
/**
 * @brief STM32746G DISCOVERY BSP Driver version number V2.0.2
   */
#define __STM32746G_DISCO_BSP_VERSION_MAIN   (0x02) /*!< [31:24] main version */
#define __STM32746G_DISCO_BSP_VERSION_SUB1   (0x00) /*!< [23:16] sub1 version */
#define __STM32746G_DISCO_BSP_VERSION_SUB2   (0x02) /*!< [15:8]  sub2 version */
#define __STM32746G_DISCO_BSP_VERSION_RC     (0x00) /*!< [7:0]  release candidate */
#define __STM32746G_DISCO_BSP_VERSION         ((__STM32746G_DISCO_BSP_VERSION_MAIN << 24)\
                                             |(__STM32746G_DISCO_BSP_VERSION_SUB1 << 16)\
                                             |(__STM32746G_DISCO_BSP_VERSION_SUB2 << 8 )\
                                             |(__STM32746G_DISCO_BSP_VERSION_RC))
/**
  * @}
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Private_Macros STM32746G_DISCOVERY_LOW_LEVEL Private Macros
  * @{
  */
/**
  * @}
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Private_Variables STM32746G_DISCOVERY_LOW_LEVEL Private Variables
  * @{
  */

const uint32_t GPIO_PIN[LEDn] = {LED1_PIN};

GPIO_TypeDef* BUTTON_PORT[BUTTONn] = {WAKEUP_BUTTON_GPIO_PORT,
                                      TAMPER_BUTTON_GPIO_PORT,
                                      KEY_BUTTON_GPIO_PORT};

const uint16_t BUTTON_PIN[BUTTONn] = {WAKEUP_BUTTON_PIN,
                                      TAMPER_BUTTON_PIN,
                                      KEY_BUTTON_PIN};

const uint16_t BUTTON_IRQn[BUTTONn] = {WAKEUP_BUTTON_EXTI_IRQn,
                                       TAMPER_BUTTON_EXTI_IRQn,
                                       KEY_BUTTON_EXTI_IRQn};

USART_TypeDef* COM_USART[COMn] = {DISCOVERY_COM1};

GPIO_TypeDef* COM_TX_PORT[COMn] = {DISCOVERY_COM1_TX_GPIO_PORT};

GPIO_TypeDef* COM_RX_PORT[COMn] = {DISCOVERY_COM1_RX_GPIO_PORT};

const uint16_t COM_TX_PIN[COMn] = {DISCOVERY_COM1_TX_PIN};

const uint16_t COM_RX_PIN[COMn] = {DISCOVERY_COM1_RX_PIN};

const uint16_t COM_TX_AF[COMn] = {DISCOVERY_COM1_TX_AF};

const uint16_t COM_RX_AF[COMn] = {DISCOVERY_COM1_RX_AF};

static I2C_HandleTypeDef hI2cAudioHandler = {0};
static I2C_HandleTypeDef hI2cExtHandler = {0};

/**
  * @}
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Private_FunctionPrototypes STM32746G_DISCOVERY_LOW_LEVEL Private Function Prototypes
  * @{
  */
static void     I2Cx_MspInit(I2C_HandleTypeDef *i2c_handler);
static void     I2Cx_Init(I2C_HandleTypeDef *i2c_handler);

static HAL_StatusTypeDef I2Cx_ReadMultiple(I2C_HandleTypeDef *i2c_handler, uint8_t Addr, uint16_t Reg, uint16_t MemAddSize, uint8_t *Buffer, uint16_t Length);
static HAL_StatusTypeDef I2Cx_WriteMultiple(I2C_HandleTypeDef *i2c_handler, uint8_t Addr, uint16_t Reg, uint16_t MemAddSize, uint8_t *Buffer, uint16_t Length);
static HAL_StatusTypeDef I2Cx_IsDeviceReady(I2C_HandleTypeDef *i2c_handler, uint16_t DevAddress, uint32_t Trials);
static void              I2Cx_Error(I2C_HandleTypeDef *i2c_handler, uint8_t Addr);

/* AUDIO IO functions */
void            AUDIO_IO_Init(void);
void            AUDIO_IO_DeInit(void);
void            AUDIO_IO_Write(uint8_t Addr, uint16_t Reg, uint16_t Value);
uint16_t        AUDIO_IO_Read(uint8_t Addr, uint16_t Reg);
void            AUDIO_IO_Delay(uint32_t Delay);

/* TOUCHSCREEN IO functions */
void            TS_IO_Init(void);
void            TS_IO_Write(uint8_t Addr, uint8_t Reg, uint8_t Value);
uint8_t         TS_IO_Read(uint8_t Addr, uint8_t Reg);
void            TS_IO_Delay(uint32_t Delay);

/* CAMERA IO functions */
void            CAMERA_IO_Init(void);
void            CAMERA_Delay(uint32_t Delay);
void            CAMERA_IO_Write(uint8_t Addr, uint8_t Reg, uint8_t Value);
uint8_t         CAMERA_IO_Read(uint8_t Addr, uint8_t Reg);

/* I2C EEPROM IO function */
void                EEPROM_IO_Init(void);
HAL_StatusTypeDef   EEPROM_IO_WriteData(uint16_t DevAddress, uint16_t MemAddress, uint8_t* pBuffer, uint32_t BufferSize);
HAL_StatusTypeDef   EEPROM_IO_ReadData(uint16_t DevAddress, uint16_t MemAddress, uint8_t* pBuffer, uint32_t BufferSize);
HAL_StatusTypeDef   EEPROM_IO_IsDeviceReady(uint16_t DevAddress, uint32_t Trials);
/**
  * @}
  */

/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Functions STM32746G_DISCOVERY_LOW_LEVELSTM32746G_DISCOVERY_LOW_LEVEL Exported Functions
  * @{
  */ 

  /**
  * @brief  This method returns the STM32746G DISCOVERY BSP Driver revision
  * @retval version: 0xXYZR (8bits for each decimal, R for RC)
  */
uint32_t BSP_GetVersion(void)
{
  return __STM32746G_DISCO_BSP_VERSION;
}

/**
  * @brief  Configures LED on GPIO.
  * @param  Led: LED to be configured. 
  *          This parameter can be one of the following values:
  *            @arg  LED1
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  gpio_init_structure;
  GPIO_TypeDef*     gpio_led;

  if (Led == LED1)
  {
    gpio_led = LED1_GPIO_PORT;
    /* Enable the GPIO_LED clock */
    LED1_GPIO_CLK_ENABLE();

    /* Configure the GPIO_LED pin */
    gpio_init_structure.Pin = GPIO_PIN[Led];
    gpio_init_structure.Mode = GPIO_MODE_OUTPUT_PP;
    gpio_init_structure.Pull = GPIO_PULLUP;
    gpio_init_structure.Speed = GPIO_SPEED_HIGH;
  
    HAL_GPIO_Init(gpio_led, &gpio_init_structure);
    
    /* By default, turn off LED */
    HAL_GPIO_WritePin(gpio_led, GPIO_PIN[Led], GPIO_PIN_RESET);
  }
}

/**
  * @brief  DeInit LEDs.
  * @param  Led: LED to be configured. 
  *          This parameter can be one of the following values:
  *            @arg  LED1
  * @note Led DeInit does not disable the GPIO clock
  * @retval None
  */
void BSP_LED_DeInit(Led_TypeDef Led)
{
  GPIO_InitTypeDef  gpio_init_structure;
  GPIO_TypeDef*     gpio_led;

  if (Led == LED1)
  {
    gpio_led = LED1_GPIO_PORT;
    /* Turn off LED */
    HAL_GPIO_WritePin(gpio_led, GPIO_PIN[Led], GPIO_PIN_RESET);
    /* Configure the GPIO_LED pin */
    gpio_init_structure.Pin = GPIO_PIN[Led];
    HAL_GPIO_DeInit(gpio_led, gpio_init_structure.Pin);
  }
}

/**
  * @brief  Turns selected LED On.
  * @param  Led: LED to be set on 
  *          This parameter can be one of the following values:
  *            @arg  LED1
  * @retval None
  */
void BSP_LED_On(Led_TypeDef Led)
{
  GPIO_TypeDef*     gpio_led;

  if (Led == LED1)	/* Switch On LED connected to GPIO */
  {
    gpio_led = LED1_GPIO_PORT;
    HAL_GPIO_WritePin(gpio_led, GPIO_PIN[Led], GPIO_PIN_SET);
  }
}

/**
  * @brief  Turns selected LED Off. 
  * @param  Led: LED to be set off
  *          This parameter can be one of the following values:
  *            @arg  LED1
  * @retval None
  */
void BSP_LED_Off(Led_TypeDef Led)
{
  GPIO_TypeDef*     gpio_led;

  if (Led == LED1) /* Switch Off LED connected to GPIO */
  {
    gpio_led = LED1_GPIO_PORT;
    HAL_GPIO_WritePin(gpio_led, GPIO_PIN[Led], GPIO_PIN_RESET);
  }
}

/**
  * @brief  Toggles the selected LED.
  * @param  Led: LED to be toggled
  *          This parameter can be one of the following values:
  *            @arg  LED1
  * @retval None
  */
void BSP_LED_Toggle(Led_TypeDef Led)
{
  GPIO_TypeDef*     gpio_led;

  if (Led == LED1)	/* Toggle LED connected to GPIO */
  {
    gpio_led = LED1_GPIO_PORT;
    HAL_GPIO_TogglePin(gpio_led, GPIO_PIN[Led]);
  }
}

/**
  * @brief  Configures button GPIO and EXTI Line.
  * @param  Button: Button to be configured
  *          This parameter can be one of the following values:
  *            @arg  BUTTON_WAKEUP: Wakeup Push Button 
  *            @arg  BUTTON_TAMPER: Tamper Push Button  
  *            @arg  BUTTON_KEY: Key Push Button
  * @param  ButtonMode: Button mode
  *          This parameter can be one of the following values:
  *            @arg  BUTTON_MODE_GPIO: Button will be used as simple IO
  *            @arg  BUTTON_MODE_EXTI: Button will be connected to EXTI line 
  *                                    with interrupt generation capability
  * @note On STM32746G-Discovery board, the three buttons (Wakeup, Tamper and key buttons)
  *       are mapped on the same push button named "User"
  *       on the board serigraphy.
  * @retval None
  */
void BSP_PB_Init(Button_TypeDef Button, ButtonMode_TypeDef ButtonMode)
{
  GPIO_InitTypeDef gpio_init_structure;
  
  /* Enable the BUTTON clock */
  BUTTONx_GPIO_CLK_ENABLE(Button);
  
  if(ButtonMode == BUTTON_MODE_GPIO)
  {
    /* Configure Button pin as input */
    gpio_init_structure.Pin = BUTTON_PIN[Button];
    gpio_init_structure.Mode = GPIO_MODE_INPUT;
    gpio_init_structure.Pull = GPIO_NOPULL;
    gpio_init_structure.Speed = GPIO_SPEED_FAST;
    HAL_GPIO_Init(BUTTON_PORT[Button], &gpio_init_structure);
  }
  
  if(ButtonMode == BUTTON_MODE_EXTI)
  {
    /* Configure Button pin as input with External interrupt */
    gpio_init_structure.Pin = BUTTON_PIN[Button];
    gpio_init_structure.Pull = GPIO_NOPULL;
    gpio_init_structure.Speed = GPIO_SPEED_FAST;
    
    if(Button != BUTTON_WAKEUP)
    {
      gpio_init_structure.Mode = GPIO_MODE_IT_FALLING; 
    }
    else
    {
      gpio_init_structure.Mode = GPIO_MODE_IT_RISING;
    }
    
    HAL_GPIO_Init(BUTTON_PORT[Button], &gpio_init_structure);
    
    /* Enable and set Button EXTI Interrupt to the lowest priority */
    HAL_NVIC_SetPriority((IRQn_Type)(BUTTON_IRQn[Button]), 0x0F, 0x00);
    HAL_NVIC_EnableIRQ((IRQn_Type)(BUTTON_IRQn[Button]));
  }
}

/**
  * @brief  Push Button DeInit.
  * @param  Button: Button to be configured
  *          This parameter can be one of the following values:
  *            @arg  BUTTON_WAKEUP: Wakeup Push Button 
  *            @arg  BUTTON_TAMPER: Tamper Push Button  
  *            @arg  BUTTON_KEY: Key Push Button
  * @note On STM32746G-Discovery board, the three buttons (Wakeup, Tamper and key buttons) 
  *       are mapped on the same push button named "User"
  *       on the board serigraphy.
  * @note PB DeInit does not disable the GPIO clock
  * @retval None
  */
void BSP_PB_DeInit(Button_TypeDef Button)
{
    GPIO_InitTypeDef gpio_init_structure;

    gpio_init_structure.Pin = BUTTON_PIN[Button];
    HAL_NVIC_DisableIRQ((IRQn_Type)(BUTTON_IRQn[Button]));
    HAL_GPIO_DeInit(BUTTON_PORT[Button], gpio_init_structure.Pin);
}


/**
  * @brief  Returns the selected button state.
  * @param  Button: Button to be checked
  *          This parameter can be one of the following values:
  *            @arg  BUTTON_WAKEUP: Wakeup Push Button 
  *            @arg  BUTTON_TAMPER: Tamper Push Button 
  *            @arg  BUTTON_KEY: Key Push Button
  * @note On STM32746G-Discovery board, the three buttons (Wakeup, Tamper and key buttons) 
  *       are mapped on the same push button named "User"
  *       on the board serigraphy.
  * @retval The Button GPIO pin value
  */
uint32_t BSP_PB_GetState(Button_TypeDef Button)
{
  return HAL_GPIO_ReadPin(BUTTON_PORT[Button], BUTTON_PIN[Button]);
}

/**
  * @brief  Configures COM port.
  * @param  COM: COM port to be configured.
  *          This parameter can be one of the following values:
  *            @arg  COM1 
  *            @arg  COM2 
  * @param  huart: Pointer to a UART_HandleTypeDef structure that contains the
  *                configuration information for the specified USART peripheral.
  * @retval None
  */
void BSP_COM_Init(COM_TypeDef COM, UART_HandleTypeDef *huart)
{
  GPIO_InitTypeDef gpio_init_structure;

  /* Enable GPIO clock */
  DISCOVERY_COMx_TX_GPIO_CLK_ENABLE(COM);
  DISCOVERY_COMx_RX_GPIO_CLK_ENABLE(COM);

  /* Enable USART clock */
  DISCOVERY_COMx_CLK_ENABLE(COM);

  /* Configure USART Tx as alternate function */
  gpio_init_structure.Pin = COM_TX_PIN[COM];
  gpio_init_structure.Mode = GPIO_MODE_AF_PP;
  gpio_init_structure.Speed = GPIO_SPEED_FAST;
  gpio_init_structure.Pull = GPIO_PULLUP;
  gpio_init_structure.Alternate = COM_TX_AF[COM];
  HAL_GPIO_Init(COM_TX_PORT[COM], &gpio_init_structure);

  /* Configure USART Rx as alternate function */
  gpio_init_structure.Pin = COM_RX_PIN[COM];
  gpio_init_structure.Mode = GPIO_MODE_AF_PP;
  gpio_init_structure.Alternate = COM_RX_AF[COM];
  HAL_GPIO_Init(COM_RX_PORT[COM], &gpio_init_structure);

  /* USART configuration */
  huart->Instance = COM_USART[COM];
  HAL_UART_Init(huart);
}

/**
  * @brief  DeInit COM port.
  * @param  COM: COM port to be configured.
  *          This parameter can be one of the following values:
  *            @arg  COM1 
  *            @arg  COM2 
  * @param  huart: Pointer to a UART_HandleTypeDef structure that contains the
  *                configuration information for the specified USART peripheral.
  * @retval None
  */
void BSP_COM_DeInit(COM_TypeDef COM, UART_HandleTypeDef *huart)
{
  /* USART configuration */
  huart->Instance = COM_USART[COM];
  HAL_UART_DeInit(huart);

  /* Enable USART clock */
  DISCOVERY_COMx_CLK_DISABLE(COM);

  /* DeInit GPIO pins can be done in the application 
     (by surcharging this __weak function) */

  /* GPIO pins clock, DMA clock can be shut down in the application 
     by surcharging this __weak function */
}

/*******************************************************************************
                            BUS OPERATIONS
*******************************************************************************/

/******************************* I2C Routines *********************************/
/**
  * @brief  Initializes I2C MSP.
  * @param  i2c_handler : I2C handler
  * @retval None
  */
static void I2Cx_MspInit(I2C_HandleTypeDef *i2c_handler)
{
  GPIO_InitTypeDef  gpio_init_structure;
  
  if (i2c_handler == (I2C_HandleTypeDef*)(&hI2cAudioHandler))
  {
    /* AUDIO and LCD I2C MSP init */

    /*** Configure the GPIOs ***/
    /* Enable GPIO clock */
    DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_CLK_ENABLE();

    /* Configure I2C Tx as alternate function */
    gpio_init_structure.Pin = DISCOVERY_AUDIO_I2Cx_SCL_PIN;
    gpio_init_structure.Mode = GPIO_MODE_AF_OD;
    gpio_init_structure.Pull = GPIO_NOPULL;
    gpio_init_structure.Speed = GPIO_SPEED_FAST;
    gpio_init_structure.Alternate = DISCOVERY_AUDIO_I2Cx_SCL_SDA_AF;
    HAL_GPIO_Init(DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_PORT, &gpio_init_structure);

    /* Configure I2C Rx as alternate function */
    gpio_init_structure.Pin = DISCOVERY_AUDIO_I2Cx_SDA_PIN;
    HAL_GPIO_Init(DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_PORT, &gpio_init_structure);

    /*** Configure the I2C peripheral ***/
    /* Enable I2C clock */
    DISCOVERY_AUDIO_I2Cx_CLK_ENABLE();

    /* Force the I2C peripheral clock reset */
    DISCOVERY_AUDIO_I2Cx_FORCE_RESET();

    /* Release the I2C peripheral clock reset */
    DISCOVERY_AUDIO_I2Cx_RELEASE_RESET();

    /* Enable and set I2Cx Interrupt to a lower priority */
    HAL_NVIC_SetPriority(DISCOVERY_AUDIO_I2Cx_EV_IRQn, 0x0F, 0);
    HAL_NVIC_EnableIRQ(DISCOVERY_AUDIO_I2Cx_EV_IRQn);

    /* Enable and set I2Cx Interrupt to a lower priority */
    HAL_NVIC_SetPriority(DISCOVERY_AUDIO_I2Cx_ER_IRQn, 0x0F, 0);
    HAL_NVIC_EnableIRQ(DISCOVERY_AUDIO_I2Cx_ER_IRQn);
  }
  else
  {
    /* External, camera and Arduino connector I2C MSP init */

    /*** Configure the GPIOs ***/
    /* Enable GPIO clock */
    DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_CLK_ENABLE();

    /* Configure I2C Tx as alternate function */
    gpio_init_structure.Pin = DISCOVERY_EXT_I2Cx_SCL_PIN;
    gpio_init_structure.Mode = GPIO_MODE_AF_OD;
    gpio_init_structure.Pull = GPIO_NOPULL;
    gpio_init_structure.Speed = GPIO_SPEED_FAST;
    gpio_init_structure.Alternate = DISCOVERY_EXT_I2Cx_SCL_SDA_AF;
    HAL_GPIO_Init(DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_PORT, &gpio_init_structure);

    /* Configure I2C Rx as alternate function */
    gpio_init_structure.Pin = DISCOVERY_EXT_I2Cx_SDA_PIN;
    HAL_GPIO_Init(DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_PORT, &gpio_init_structure);

    /*** Configure the I2C peripheral ***/
    /* Enable I2C clock */
    DISCOVERY_EXT_I2Cx_CLK_ENABLE();

    /* Force the I2C peripheral clock reset */
    DISCOVERY_EXT_I2Cx_FORCE_RESET();

    /* Release the I2C peripheral clock reset */
    DISCOVERY_EXT_I2Cx_RELEASE_RESET();

    /* Enable and set I2Cx Interrupt to a lower priority */
    HAL_NVIC_SetPriority(DISCOVERY_EXT_I2Cx_EV_IRQn, 0x0F, 0);
    HAL_NVIC_EnableIRQ(DISCOVERY_EXT_I2Cx_EV_IRQn);

    /* Enable and set I2Cx Interrupt to a lower priority */
    HAL_NVIC_SetPriority(DISCOVERY_EXT_I2Cx_ER_IRQn, 0x0F, 0);
    HAL_NVIC_EnableIRQ(DISCOVERY_EXT_I2Cx_ER_IRQn);
  }
}

/**
  * @brief  Initializes I2C HAL.
  * @param  i2c_handler : I2C handler
  * @retval None
  */
static void I2Cx_Init(I2C_HandleTypeDef *i2c_handler)
{
  if(HAL_I2C_GetState(i2c_handler) == HAL_I2C_STATE_RESET)
  {
    if (i2c_handler == (I2C_HandleTypeDef*)(&hI2cAudioHandler))
    {
      /* Audio and LCD I2C configuration */
      i2c_handler->Instance = DISCOVERY_AUDIO_I2Cx;
    }
    else
    {
      /* External, camera and Arduino connector  I2C configuration */
      i2c_handler->Instance = DISCOVERY_EXT_I2Cx;
    }
    i2c_handler->Init.Timing           = DISCOVERY_I2Cx_TIMING;
    i2c_handler->Init.OwnAddress1      = 0;
    i2c_handler->Init.AddressingMode   = I2C_ADDRESSINGMODE_7BIT;
    i2c_handler->Init.DualAddressMode  = I2C_DUALADDRESS_DISABLE;
    i2c_handler->Init.OwnAddress2      = 0;
    i2c_handler->Init.GeneralCallMode  = I2C_GENERALCALL_DISABLE;
    i2c_handler->Init.NoStretchMode    = I2C_NOSTRETCH_DISABLE;

    /* Init the I2C */
    I2Cx_MspInit(i2c_handler);
    HAL_I2C_Init(i2c_handler);
  }
}

/**
  * @brief  Reads multiple data.
  * @param  i2c_handler : I2C handler
  * @param  Addr: I2C address
  * @param  Reg: Reg address 
  * @param  MemAddress: Memory address 
  * @param  Buffer: Pointer to data buffer
  * @param  Length: Length of the data
  * @retval Number of read data
  */
static HAL_StatusTypeDef I2Cx_ReadMultiple(I2C_HandleTypeDef *i2c_handler,
                                           uint8_t Addr,
                                           uint16_t Reg,
                                           uint16_t MemAddress,
                                           uint8_t *Buffer,
                                           uint16_t Length)
{
  HAL_StatusTypeDef status = HAL_OK;

  status = HAL_I2C_Mem_Read(i2c_handler, Addr, (uint16_t)Reg, MemAddress, Buffer, Length, 1000);

  /* Check the communication status */
  if(status != HAL_OK)
  {
    /* I2C error occurred */
    I2Cx_Error(i2c_handler, Addr);
  }
  return status;    
}

/**
  * @brief  Writes a value in a register of the device through BUS in using DMA mode.
  * @param  i2c_handler : I2C handler
  * @param  Addr: Device address on BUS Bus.  
  * @param  Reg: The target register address to write
  * @param  MemAddress: Memory address 
  * @param  Buffer: The target register value to be written 
  * @param  Length: buffer size to be written
  * @retval HAL status
  */
static HAL_StatusTypeDef I2Cx_WriteMultiple(I2C_HandleTypeDef *i2c_handler,
                                            uint8_t Addr,
                                            uint16_t Reg,
                                            uint16_t MemAddress,
                                            uint8_t *Buffer,
                                            uint16_t Length)
{
  HAL_StatusTypeDef status = HAL_OK;
  
  status = HAL_I2C_Mem_Write(i2c_handler, Addr, (uint16_t)Reg, MemAddress, Buffer, Length, 1000);
  
  /* Check the communication status */
  if(status != HAL_OK)
  {
    /* Re-Initiaize the I2C Bus */
    I2Cx_Error(i2c_handler, Addr);
  }
  return status;
}

/**
  * @brief  Checks if target device is ready for communication. 
  * @note   This function is used with Memory devices
  * @param  i2c_handler : I2C handler
  * @param  DevAddress: Target device address
  * @param  Trials: Number of trials
  * @retval HAL status
  */
static HAL_StatusTypeDef I2Cx_IsDeviceReady(I2C_HandleTypeDef *i2c_handler, uint16_t DevAddress, uint32_t Trials)
{ 
  return (HAL_I2C_IsDeviceReady(i2c_handler, DevAddress, Trials, 1000));
}

/**
  * @brief  Manages error callback by re-initializing I2C.
  * @param  i2c_handler : I2C handler
  * @param  Addr: I2C Address
  * @retval None
  */
static void I2Cx_Error(I2C_HandleTypeDef *i2c_handler, uint8_t Addr)
{
  /* De-initialize the I2C communication bus */
  HAL_I2C_DeInit(i2c_handler);
  
  /* Re-Initialize the I2C communication bus */
  I2Cx_Init(i2c_handler);
}

/*******************************************************************************
                            LINK OPERATIONS
*******************************************************************************/

/********************************* LINK AUDIO *********************************/

/**
  * @brief  Initializes Audio low level.
  * @retval None
  */
void AUDIO_IO_Init(void) 
{
  I2Cx_Init(&hI2cAudioHandler);
}

/**
  * @brief  Deinitializes Audio low level.
  * @retval None
  */
void AUDIO_IO_DeInit(void)
{
}

/**
  * @brief  Writes a single data.
  * @param  Addr: I2C address
  * @param  Reg: Reg address 
  * @param  Value: Data to be written
  * @retval None
  */
void AUDIO_IO_Write(uint8_t Addr, uint16_t Reg, uint16_t Value)
{
  uint16_t tmp = Value;
  
  Value = ((uint16_t)(tmp >> 8) & 0x00FF);
  
  Value |= ((uint16_t)(tmp << 8)& 0xFF00);
  
  I2Cx_WriteMultiple(&hI2cAudioHandler, Addr, Reg, I2C_MEMADD_SIZE_16BIT,(uint8_t*)&Value, 2);
}

/**
  * @brief  Reads a single data.
  * @param  Addr: I2C address
  * @param  Reg: Reg address 
  * @retval Data to be read
  */
uint16_t AUDIO_IO_Read(uint8_t Addr, uint16_t Reg)
{
  uint16_t read_value = 0, tmp = 0;
  
  I2Cx_ReadMultiple(&hI2cAudioHandler, Addr, Reg, I2C_MEMADD_SIZE_16BIT, (uint8_t*)&read_value, 2);
  
  tmp = ((uint16_t)(read_value >> 8) & 0x00FF);
  
  tmp |= ((uint16_t)(read_value << 8)& 0xFF00);
  
  read_value = tmp;
  
  return read_value;
}

/**
  * @brief  AUDIO Codec delay 
  * @param  Delay: Delay in ms
  * @retval None
  */
void AUDIO_IO_Delay(uint32_t Delay)
{
  HAL_Delay(Delay);
}

/********************************* LINK CAMERA ********************************/

/**
  * @brief  Initializes Camera low level.
  * @retval None
  */
void CAMERA_IO_Init(void) 
{
  I2Cx_Init(&hI2cExtHandler);
}

/**
  * @brief  Camera writes single data.
  * @param  Addr: I2C address
  * @param  Reg: Register address 
  * @param  Value: Data to be written
  * @retval None
  */
void CAMERA_IO_Write(uint8_t Addr, uint8_t Reg, uint8_t Value)
{
  I2Cx_WriteMultiple(&hI2cExtHandler, Addr, (uint16_t)Reg, I2C_MEMADD_SIZE_8BIT,(uint8_t*)&Value, 1);
}

/**
  * @brief  Camera reads single data.
  * @param  Addr: I2C address
  * @param  Reg: Register address 
  * @retval Read data
  */
uint8_t CAMERA_IO_Read(uint8_t Addr, uint8_t Reg)
{
  uint8_t read_value = 0;

  I2Cx_ReadMultiple(&hI2cExtHandler, Addr, Reg, I2C_MEMADD_SIZE_8BIT, (uint8_t*)&read_value, 1);

  return read_value;
}

/**
  * @brief  Camera delay 
  * @param  Delay: Delay in ms
  * @retval None
  */
void CAMERA_Delay(uint32_t Delay)
{
  HAL_Delay(Delay);
}

/******************************** LINK I2C EEPROM *****************************/

/**
  * @brief  Initializes peripherals used by the I2C EEPROM driver.
  * @retval None
  */
void EEPROM_IO_Init(void)
{
  I2Cx_Init(&hI2cExtHandler);
}

/**
  * @brief  Write data to I2C EEPROM driver in using DMA channel.
  * @param  DevAddress: Target device address
  * @param  MemAddress: Internal memory address
  * @param  pBuffer: Pointer to data buffer
  * @param  BufferSize: Amount of data to be sent
  * @retval HAL status
  */
HAL_StatusTypeDef EEPROM_IO_WriteData(uint16_t DevAddress, uint16_t MemAddress, uint8_t* pBuffer, uint32_t BufferSize)
{
  return (I2Cx_WriteMultiple(&hI2cExtHandler, DevAddress, MemAddress, I2C_MEMADD_SIZE_16BIT, pBuffer, BufferSize));
}

/**
  * @brief  Read data from I2C EEPROM driver in using DMA channel.
  * @param  DevAddress: Target device address
  * @param  MemAddress: Internal memory address
  * @param  pBuffer: Pointer to data buffer
  * @param  BufferSize: Amount of data to be read
  * @retval HAL status
  */
HAL_StatusTypeDef EEPROM_IO_ReadData(uint16_t DevAddress, uint16_t MemAddress, uint8_t* pBuffer, uint32_t BufferSize)
{
  return (I2Cx_ReadMultiple(&hI2cExtHandler, DevAddress, MemAddress, I2C_MEMADD_SIZE_16BIT, pBuffer, BufferSize));
}

/**
  * @brief  Checks if target device is ready for communication. 
  * @note   This function is used with Memory devices
  * @param  DevAddress: Target device address
  * @param  Trials: Number of trials
  * @retval HAL status
  */
HAL_StatusTypeDef EEPROM_IO_IsDeviceReady(uint16_t DevAddress, uint32_t Trials)
{ 
  return (I2Cx_IsDeviceReady(&hI2cExtHandler, DevAddress, Trials));
}

/********************************* LINK TOUCHSCREEN *********************************/

/**
  * @brief  Initializes Touchscreen low level.
  * @retval None
  */
void TS_IO_Init(void)
{
  I2Cx_Init(&hI2cAudioHandler);
}

/**
  * @brief  Writes a single data.
  * @param  Addr: I2C address
  * @param  Reg: Reg address
  * @param  Value: Data to be written
  * @retval None
  */
void TS_IO_Write(uint8_t Addr, uint8_t Reg, uint8_t Value)
{
  I2Cx_WriteMultiple(&hI2cAudioHandler, Addr, (uint16_t)Reg, I2C_MEMADD_SIZE_8BIT,(uint8_t*)&Value, 1);
}

/**
  * @brief  Reads a single data.
  * @param  Addr: I2C address
  * @param  Reg: Reg address
  * @retval Data to be read
  */
uint8_t TS_IO_Read(uint8_t Addr, uint8_t Reg)
{
  uint8_t read_value = 0;

  I2Cx_ReadMultiple(&hI2cAudioHandler, Addr, Reg, I2C_MEMADD_SIZE_8BIT, (uint8_t*)&read_value, 1);

  return read_value;
}

/**
  * @brief  TS delay
  * @param  Delay: Delay in ms
  * @retval None
  */
void TS_IO_Delay(uint32_t Delay)
{
  HAL_Delay(Delay);
}

/**
  * @}
  */

/**
  * @}
  */ 

/**
  * @}
  */

/**
  * @}
  */    
    
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/